Wasp-bar-code WPS100 Manual do Utilizador Página 181
- Página / 466
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
7-61
Symbologies
Set Lengths for Discrete 2 of 5 (Continued)
Length Within Range - This option allows you to decode an D 2 of 5 symbol with a
specific length range. The length range is selected from numeric bar codes beginning
on page D-1 in Appendix D. For example, to decode D 2 of 5 symbols containing
between 4 and 12 characters, first scan D 2 of 5 - Length Within Range. Then scan 0, 4,
1, and 2 (single digit numbers must always be preceded by a leading zero). If you make an
error or wish to change your selection, scan Cancel on page D-5.
D 2 of 5 - Length Within Range
Any Length - Scanning this option allows you to decode D 2 of 5 symbols containing any
number of characters within the scanner capability.
Note: Due to the construction of the D 2 of 5 symbology, it is possible for a
scan line covering only a portion of the code to be interpreted as a
complete scan, yielding less data than is actually encoded in the bar
code. To prevent this from happening, it is recommended that
specific lengths (D 2 of 5 - One Discrete Length - Two Discrete
Lengths) be selected for D 2 of 5 applications.
D 2 of 5 - Any Length
- Product Reference Guide 1
- Wasp Technologies, Inc 4
- 1400 10th Street 4
- Plano, TX 75074 4
- Contents 5
- Chapter 6 7
- Appendix D 11
- Numeric Bar Codes 11
- Glossary 11
- About This Guide 13
- Notational Conventions 15
- Related Publications 15
- Wasp Technical Support 15
- Chapter 1 17
- Getting Started 17
- Unpacking Your Scanner 18
- Setting Up the Scanner 19
- Configuring Your Scanner 20
- Removing the Interface Cable 20
- Chapter 2 21
- Scanning 21
- Scanning in Single-Line Mode 22
- Scanning in Omni Mode 23
- Figure 2-8. “Swipe” scanning 26
- Beeper Definitions 27
- LED Definitions 29
- Specular 30
- Reflection 30
- Decode Zone 31
- Chapter 3 33
- Troubleshooting 34
- Technical Specifications 36
- Scanner Signal Descriptions 39
- Chapter 4 41
- User Preferences 41
- Parameter Default 44
- Beeper Tone 46
- *High Frequency 46
- Beeper Volume 47
- *High Volume 47
- Volume Change Trigger Delay 48
- Laser On Time 49
- Beep After Good Decode 50
- *Beep After Good Decode 50
- Low Power Blink 51
- *Low Power - Blink Mode 51
- Scan Pattern Mode 52
- Single-Line Aim Duration 53
- Aim Duration 4 sec 54
- Aim Duration 5 sec 54
- Timeout Between Decodes 55
- Time Delay to Low Power Mode 56
- 60 Minutes 57
- 90 Minutes 57
- Linear UPC/EAN Decode 58
- Chapter 5 59
- Keyboard Wedge Interface 59
- Power supply 60
- (if needed) 60
- Male DIN Keyboard 60
- Keyboard Wedge Host Types 62
- NCR 7052 63
- *North American 64
- French Canadian Win 95/98 65
- Spanish Windows 65
- Italian Windows 66
- Swedish Windows 66
- UK English Windows 66
- Japanese Windows 67
- Brazilian/Portuguese Windows 67
- Ignore Unknown Characters 68
- *Send Bar Codes With Unknown 68
- Keystroke Delay 69
- Intra-Keystroke Delay 70
- Caps Lock On 72
- *Disable Caps Lock On 72
- Caps Lock Override 73
- *Disable Caps Lock Override 73
- Convert Wedge Data 74
- *No Convert 74
- FN1 Substitution 76
- Send Make Break 77
- Keyboard Maps 78
- Figure 5-4. IBM PC/AT 79
- Figure 5-5. NCR 7052 32-KEY 79
- Figure 5-6. NCR 7052 58-KEY 80
- Connecting a USB Interface 94
- USB Default Parameters 96
- USB Host Parameters 97
- French, Windows 98
- German, Windows 98
- French Canadian, Windows 99
- Swedish, Windows 100
- UK English, Windows 100
- Italian, Windows 100
- USB Interface 101
- Portuguese-Brazilian, Windows 101
- Japanese, Windows (ASCII) 101
- USB Keystroke Delay 102
- *No Delay 102
- USB CAPS Lock Override 103
- USB Ignore Unknown Characters 104
- Emulate Keypad 105
- USB Keyboard FN1 Substitution 106
- Function Key Mapping 107
- Simulated Caps Lock 108
- Convert Case 109
- ASCII Character Set 110
- Chapter 7 121
- Symbologies 121
- Scanning Sequence Examples 122
- Errors While Scanning 122
- Symbology Default Parameters 123
- Enable/Disable UPC-A/UPC-E 128
- *Enable UPC-A 128
- *Enable UPC-E 128
- Enable/Disable UPC-E1 129
- *Disable UPC-E1 129
- *Enable EAN-13/JAN-13 130
- *Enable EAN-8/JAN-8 130
- Enable/Disable Bookland EAN 131
- *Disable Bookland EAN 131
- Decode UPC/EAN Supplementals 132
- Ignore Supplementals 133
- Enable 978 Supplemental Mode 134
- *Transmit UPC-A Check Digit 136
- *Transmit UPC-E1 Check Digit 137
- UPC-A Preamble 138
- *System Character 138
- UPC-A Preamble (Continued) 139
- UPC-E Preamble 139
- UPC-E Preamble (Continued) 140
- UPC-E1 Preamble 140
- UPC-E1 Preamble (Continued) 141
- Convert UPC-E to UPC-A 141
- Convert UPC-E1 to UPC-A 142
- EAN Zero Extend 143
- *Disable EAN Zero Extend 143
- UCC Coupon Extended Code 144
- Code 128 145
- Enable/Disable UCC/EAN-128 146
- *Enable UCC/EAN-128 146
- Enable/Disable ISBT 128 147
- *Enable ISBT 128 147
- Code 128 Decode Performance 148
- Enable/Disable Code 39 150
- *Enable Code 39 150
- *Disable Trioptic Code 39 151
- Convert Code 39 to Code 32 152
- Code 32 Prefix 153
- *Disable Code 32 Prefix 153
- Set Lengths for Code 39 154
- Code 39 - Length Within Range 155
- Code 39 - Any Length 155
- *Disable Code 39 Check Digit 156
- Transmit Code 39 Check Digit 157
- *Disable Code 39 Full ASCII 158
- Buffer Code 39 159
- (Enable) 159
- Buffer Data 160
- Clear Transmission Buffer 160
- Transmit Buffer 161
- Code 39 Decode Performance 163
- Enable/Disable Code 93 165
- *Disable Code 93 165
- Set Lengths for Code 93 166
- Code 93 - Length Within Range 167
- Code 93 - Any Length 167
- *Disable Code 11 168
- Set Lengths for Code 11 169
- Code 11 - Length Within Range 170
- Code 11 - Any Length 170
- *One Check Digit 171
- Transmit Code 11 Check Digits 172
- Interleaved 2 of 5 (ITF) 173
- I 2 of 5 - Any Length 175
- *Disable 176
- Transmit I 2 of 5 Check Digit 177
- Convert I 2 of 5 to EAN-13 178
- Discrete 2 of 5 (DTF) 179
- D 2 of 5 - Any Length 181
- Chinese 2 of 5 182
- Codabar (NW - 7) 183
- Set Lengths for Codabar 184
- Codabar - Length Within Range 185
- Codabar - Any Length 185
- CLSI Editing 186
- *Disable CLSI Editing 186
- NOTIS Editing 187
- *Disable NOTIS Editing 187
- Enable/Disable MSI 188
- *Disable MSI 188
- Set Lengths for MSI 189
- MSI - Length Within Range 190
- MSI - Any Length 190
- MSI Check Digits 191
- *One MSI Check Digit 191
- Transmit MSI Check Digit(s) 192
- MSI Check Digit Algorithm 193
- *MOD 10/MOD 10 193
- RSS (Reduced Space Symbology) 194
- RSS Limited 195
- *Disable RSS Limited 195
- RSS Expanded 196
- Convert RSS to UPC/EAN 197
- XXXXXXXXXXXX 198
- XXXXXXXXXXX 198
- 0 1000000XXXXXXXX 198
- Enable Convert RSS to UPC/EAN 199
- Redundancy Level 200
- *Redundancy Level 1 200
- Redundancy Level 2 201
- Redundancy Level 3 201
- Redundancy Level 4 202
- Security Level 203
- * Security Level 0 203
- Security Level 2 204
- Security Level 3 204
- *Normal Intercharacter Gaps 205
- Chapter 8 207
- Miscellaneous Scanner Options 207
- Transmit Code ID Character 210
- Prefix/Suffix Values 211
- Set Value 3 212
- Set Value 4 212
- Set Value 5 213
- FN1 Substitution Values 214
- Scan Data Options 215
- *Data As Is 216
- <DATA> <SUFFIX> 216
- <PREFIX> <DATA> 216
- Data Format Cancel 217
- Transmit “No Read” Message 218
- *Disable No Read 218
- Chapter 9 219
- Advanced Data Formatting 219
- Using ADF Bar Codes 220
- ADF Bar Code Menu Example 220
- Rule 2: The UPC Scanning Rule 221
- Alternate Rule Sets 222
- Default Rules 224
- Special Commands 225
- Save Rule 226
- Erase (Continued) 227
- Quit Entering Rules 227
- Disable Rule Set 228
- Disable Rule Set (Continued) 229
- Criteria 230
- Code Types (Continued) 231
- Code Lengths 238
- Code Lengths (Continued) 239
- Specific String at Start 248
- Any Message OK 249
- Rule Belongs To Set 250
- Rule Belongs To Set 3 251
- Rule Belongs To Set 4 251
- Send Data 252
- Send Data (Continued) 253
- Setup Field(s) 260
- Move Cursor 261
- Move Cursor (Continued) 262
- Skip Ahead 262
- Skip Ahead (Continued) 263
- Skip Back 266
- Skip Back (Continued) 267
- Send Preset Value 269
- Send Preset Value (Continued) 270
- Modify Data 271
- Modify Data (Continued) 272
- Pad Data with Zeros 284
- Stop Pad Zeros 294
- Beep Once 294
- Beep Twice 294
- Beeps (Continued) 295
- Characters) 295
- Send Control C 296
- Send Control B 296
- Send Control D 296
- Send Control E 297
- Send Control G 297
- Send Control F 297
- Send Control H 298
- Send Control I 298
- Send Control J 298
- Send Control K 299
- Send Control L 299
- Send Control M 299
- Send Control P 300
- Send Control O 300
- Send Control N 300
- Send Control Q 301
- Send Control S 301
- Send Control R 301
- Send Control T 302
- Send Control U 302
- Send Control V 302
- Send Control X 303
- Send Control Y 303
- Send Control W 303
- Send Control [ 304
- Send Control Z 304
- Send Control \ 304
- Send Control ] 305
- Send Control 305
- Send Control 6 305
- Keyboard Characters 306
- Send & 308
- Send < 315
- Send > 316
- Send ALT Characters 337
- Send Alt A 338
- Send Alt C 338
- Send Alt B 338
- Send Alt D 339
- Send Alt E 339
- Send Alt F 339
- Send Alt H 340
- Send Alt I 340
- Send Alt G 340
- Send Alt K 341
- Send Alt J 341
- Send Alt L 341
- Send Alt M 342
- Send Alt O 342
- Send Alt N 342
- Send Alt P 343
- Send Alt Q 343
- Send Alt R 343
- Send Alt S 344
- Send Alt T 344
- Send Alt U 344
- Send Alt X 345
- Send Alt V 345
- Send Alt W 345
- Send Alt Y 346
- Send Alt [ 346
- Send Alt Z 346
- Send Alt \ 347
- Send Alt ] 347
- Send Alt 6 347
- Send Keypad Characters 348
- Send Keypad 349
- Send Keypad / 349
- Send Keypad 0 350
- Send Keypad 2 350
- Send Keypad 1 350
- Send Keypad 5 351
- Send Keypad 4 351
- Send Keypad 3 351
- Send Keypad 6 352
- Send Keypad 8 352
- Send Keypad 7 352
- Send Keypad 9 353
- Send Keypad Enter 353
- Send Keypad Numlock 353
- Send Break Key 354
- Send Delete Key 354
- Send Page Up Key 354
- Send End Key 355
- Send Page Down Key 355
- Send Pause Key 355
- Send Backspace Key 356
- Send Scroll Lock Key 356
- Send Tab Key 356
- Send Insert Key 357
- Send Home Key 357
- Send Print Screen Key 357
- Send Enter Key 358
- Send Up Arrow Key 358
- Send Escape Key 358
- Send Left Arrow Key 359
- Send Down Arrow Key 359
- Send Right Arrow Key 359
- Send Function Key 360
- Send Function Key (Continued) 361
- Send Right Control Key 380
- Send GUI 2 381
- Send GUI 1 381
- Send GUI 0 381
- Send GUI 5 382
- Send GUI 4 382
- Send GUI 3 382
- Send GUI 8 383
- Send GUI 7 383
- Send GUI 6 383
- Send GUI B 384
- Send GUI A 384
- Send GUI 9 384
- Send GUI E 385
- Send GUI D 385
- Send GUI C 385
- Send GUI H 386
- Send GUI G 386
- Send GUI F 386
- Send GUI K 387
- Send GUI J 387
- Send GUI I 387
- Send GUI N 388
- Send GUI M 388
- Send GUI L 388
- Send GUI Q 389
- Send GUI P 389
- Send GUI O 389
- Send GUI T 390
- Send GUI S 390
- Send GUI R 390
- Send GUI W 391
- Send GUI V 391
- Send GUI U 391
- Send GUI Z 392
- Send GUI Y 392
- Send GUI X 392
- Turn On/Off Rule Sets 393
- Turn On Rule Set 4 394
- Turn On Rule Set 3 394
- Turn Off Rule Set 1 394
- Turn Off Rule Set 2 395
- Turn Off Rule Set 4 395
- Turn Off Rule Set 3 395
- Alphanumeric Keyboard 396
- End Of Message 417
- Appendix A 429
- Standard Default Parameters 429
- Appendix B 437
- Programming Reference 437
- M Code 39 Trioptic 438
- N Coupon Code 438
- Code Character Code Type 438
- AIM Code Identifiers 439
- Appendix C 445
- Sample Bar Codes 445
- UPC/EAN (Continued) 446
- Interleaved 2 of 5 446
- 7612341562341 447
- Appendix D 449
- Glossary-2 456
- Glossary-3 457
- Glossary-4 458
- Glossary-5 459
- Glossary-6 460
- Revision A 466
Manuais e produtos relacionados com Scanners Wasp-bar-code WPS100
Scanners Wasp-bar-code WLS 9500 Manual do Utilizador
(189 páginas)
(189 páginas)
Scanners Wasp-bar-code WWS800 Manual do Utilizador
(22 páginas)
(22 páginas)
Scanners Wasp-bar-code WWS850 Manual do Utilizador
(30 páginas)
(30 páginas)
Scanners Wasp-bar-code WDT3200 Manual do Utilizador
(28 páginas)
(28 páginas)
Scanners Wasp-bar-code WWR2900 Manual do Utilizador
(44 páginas)
(44 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais